Markel K3423T Heavy Duty Fan Forced Electric Wall Heater, 3000 Watts, 240V/3Ph
Markel
(No reviews yet)
Write a Review
Write a Review
Markel
Markel K3423T Heavy Duty Fan Forced Electric Wall Heater, 3000 Watts, 240V/3Ph
$1,339.00
Usually Ships In 2-3 Weeks
Free ground shipping to the lower 48 states
- Product ID:
- Markel-K3423T
- UPC:
- 686334384650
- Weight:
- 41.00 (Lbs.)
- Ships By:
- Free Ground
- Ships From:
- Tennessee - Direct From Markel
Markel K3423T Heavy Duty Fan Forced Electric Wall Heater Features:
- Not cancelable, not returnable. Before purchasing please double check to confirm this item is correct for your application.
- Catalog Number: 03846502.
- Model Number: K3423T.
- Agency Rating: ETL-CUS.
- Wattage: 3000.
- BTU: 10239.
- Voltage: 240.
- Phase: 3.
- Amp: 7.3.
- CFM: 245.
- Weight (lbs): 41.
- Model Number: K3423T.
- Agency Rating: ETL-CUS.
- Wattage: 3000.
- BTU: 10239.
- Voltage: 240.
- Phase: 3.
- Amp: 7.3.
- CFM: 245.
- Weight (lbs): 41.
Additional Features
- Powder coated bar stock steel tamper proof grille, with extruded Aluminum and 16 gauge housing.
- In-built tamper proof thermostat.
- Manual reset thermal limit switch.
- Corrosion resistant steel tubular element with brazed steel fins.
- Permanently lubricated, unit bearing, shaded pole motor with impedance protection.
- Propeller type fan blade.
- Made in U.S.A.
- California residents see Prop 65 Warnings.
- In-built tamper proof thermostat.
- Manual reset thermal limit switch.
- Corrosion resistant steel tubular element with brazed steel fins.
- Permanently lubricated, unit bearing, shaded pole motor with impedance protection.
- Propeller type fan blade.
- Made in U.S.A.
- California residents see Prop 65 Warnings.
Additional Information
The heater shall so be designed to provide an even distribution of heated air to the space to be heated by drawing return air in the peripheral area of the heater across and through the element which shall then be discharged from the center section of the heater by means of an electric motor and axial flow fan blade. Heaters shall be recessed type to extend no more than 1 1/2” from the finished wall or surface mounted to extend no more than 5 3/4” from the finished wall or semi-recessed type to extend no more than 3 1/2” from finished wall or semi-recessed type to extend no more than 2 1/2” from finished wall.
ENCLOSURE: Heater front shall withstand 10.8 ft. lbs. (324 poundals) impact and 400 lbs. static force applied to an 8 sq. in. area at center grille location with less than 1/16” permanent distortion. The combination return and supply grille assembly shall be constructed of 1/16” x 3/8” rounded edge horizontal steel louvers which shall be spaced for maximum opening of 1/4”. Louvers shall be welded at every intersection to three evenly spaced 1/16” diameter vertical members and completely framed in a heavy gauge natural anodized Aluminum extrusion or alternate silver painted steel. Front assembly shall be attached to the chassis by hidden tamper-resistant (Allen-head) machine screws. All other parts shall be 16 gauge steel Zinc coated, both sides finished in a bronze colored baked powder coat finish.
MOTOR: Motor shall be a permanently lubricated unit bearing, totally enclosed shaded pole type with impedance protection. Motors shall operate at no more than 1400 RPM and shall be same voltage as the heater. A protective shield shall surround the motor to separate return air from heated air.
PERFORMANCE: Heaters shall have a rating of 245 CFM at 660 F.P.M. with a maximum temperature rise of 64°F.
ELEMENTS: Element assemblies shall consist of corrosion resistant steel sheathed type elements mechanically bonded to common corrosion resistant steel fins. Each sheathed element shall consist of helically coiled Nickel Chromium alloy resistant wire completely embedded in and surrounded by Magnesium Oxide, enclosed and compacted into corrosion resistant steel sheaths. Elements shall have 2” cold conductor pins extending into the sheath and shall have a density of no more than 60 Watts per inch.
THERMAL OVERLOAD: Heaters shall be equipped with a “manual reset” thermal overload which disconnects elements and motor in the event normal operating temperatures are exceeded. For safety, if opened due to abnormal temperature, thermal overload shall remain open until manually reset. Automatic reset thermal overloads which allow the element to continue to cycle under abnormal conditions shall not be accepted.
APPROVAL: Heaters shall be ETL Listed.
CONTROL SYSTEM: Heaters will be provided with thermostat of the tamper-proof hydraulic design with a temperature range of 40°F - 120°F. The thermostat will serve as a disconnect switch in the “off” position, breaking all ungrounded conductors.
Related Units, Accessories, And OEM Replacement Parts
From Our
Fans
"We have been ordering parts from NorthStock and have been very pleased with the service... Customer service on a level that you do not see very often this day and age. Thanks NorthStock!"
CRYSTAL FROM FLORIDA
"This company cares about their products but also cares about customer satisfaction. I will continue to order from them for all my needs."
pat from pennsylvania
"I ordered a part to be shipped to Arkansas. NorthStock had the best price that I could find. They shipped the part fast and it (fan motor) runs quieter than when new."
tim from arkansas
"Excellent customer service and quicker than expected delivery of a hard to source part. Highly recommended."
sean from massachusetts
"Had exactly what I needed in stock. Ordered on a Wednesday and it arrived Friday. Could not ask for better service. Fast Shipping and a very nice website!""
scott from maryland
"Fast shipping and excellent customer service. Will continue to do business with them."
andrew from missouri