QMark LFK151F Fan-Forced Wall Heater, 1,500W, 120V 1PH 12.5A
QMark
(No reviews yet)
Write a Review
Write a Review
QMark
QMark LFK151F Fan-Forced Wall Heater, 1,500W, 120V 1PH 12.5A
$419.57
4 In Stock, Orders Placed By 3pm EST Ship Same Day (Weekends And Holidays Excluded)
Free ground shipping to the lower 48 states
- Product ID:
- QMark-LFK151F
- UPC:
- 685360162683
- Weight:
- 22.00 (Lbs.)
- Ships By:
- Free Ground, Or Choose Expedited Shipping At Checkout
- Ships From:
- NorthStock In Massachusetts
Description:
QMark LFK151F Fan-Forced Wall Heater, 1,500W, 120V 1PH 12.5A
The Qmark LFK series electric fan forced wall heater is designed for light duty commercial and residential applications. Entryways, vestibules, offices, reception rooms, game rooms, and family rooms stay warm and cozy when you install this fan-forced heater. Its high-capacity heating power is ideal for basements and playrooms, too. The unit is easy to install, thanks to its simple 3-piece design and integrated thermostat. Its fan delay feature helps prolong the life of your heater, too.
QMark LFK Series Fan-Forced Wall Heater Features:
- Contemporary commercial-grade steel grille designed to provide a clean appearance and rugged use.
- Manual reset thermal overheat protector disconnects power in the event of accidental blockage.
- Automatic fan delay eliminates cold drafts on start-up and discharges residual heat from the heater body during shut down.
- Integral double-pole thermostat allows for easy adjustment of room temperature to maintain desired comfort level.
- Positive OFF switch to assure heater will not operate if not needed.
- All units have a permanently lubricated enclosed fan motor, which creates long life, low maintenance, and distributes warmth throughout the area.
- Tamper-proof plug for thermostat hole.
ARCHITECT’S AND ENGINEER’S SPECIFICATIONS*
The heating equipment shall include an electric automatic fan forced air heater suitable for small area heating, as manufactured by QMark®, a Marley Engineered Products® Brand, Bennettsville, SC. The heater shall be designed for wall mounting, recess or surface. Heaters shall be cETLus listed.
BACK BOX: The back box shall be designed as a recessed rough-in box in either masonry or frame installations and is also used when surface mounting frames are used in surface mounting installations. The back box shall be heavy gauge galvanized steel and shall contain knockouts through which power leads enter.
INNER FRAME ASSEMBLY: The heater assembly, which fits into the back box, shall consist of a heavy gauge steel fan panel to which all of the operational parts of the heater are mounted. The inner frame assembly shall be completely prewired.
HEATING ELEMENT: The heating element shall be of the non-glowing design consisting of an 80/20 nickel-chromium resistance wire enclosed in a steel sheath to which plate fins are copper brazed. The element shall cover the entire air discharge area to ensure uniform heating of all discharged air. It shall be warrantied for 5 years.
MOTOR AND CONTROLS: The fan motor shall be totally enclosed, impedance protected, permanently lubricated and with a totally enclosed rotor. Fan control shall be of the bimetallic, snap-action type and shall activate fan after heating element reaches operating temperature, and continue to operate the fan after the thermostat is satisfied and until all heated air has been discharged. The thermostat shall be single-pole type on all models. Thermal cutout shall be bimetallic, snap-action type designed to shut off heat in the event of overheating. The fan shall be five-bladed aluminum.
SURFACE MOUNTING FRAME: The surface mounting frame shall be of heavy gauge steel designed to mount around the back box for a finished surface installation. Slot knock outs shall be provided for power supply conduit.
FRONT COVER: The louvered front cover shall be of heavy gauge steel with a powder paint finish. A plug button will be provided to replace the thermostat knob and render the unit tamper-resistant.
FINISH: All sheet metal parts, except the galvanized steel back box, shall be phosphatized, then completely painted by a powder paint process.
*In the interest of continual improvements in product and performance, Marley Engineered Products reserves the right to change specifications without notice.
Related Units, Accessories, And OEM Replacement Parts
